MH CD-42 Charge Discharge Module

This 150W DC-DC Boost Converter 10-32V to 12-35V module allows you to step up an input voltage as low as 10V and set the output to 12V-35V. The output voltage will be higher than the input voltage. In addition the boost converter design is based on popular Texas Instrument’s UC3844 current mode PWM controller chip.

4A Buck Boost Converter Module Adjustable Step Up and Step Down Function with LCD Display Power (HW-140) Function Description: The module has IN/OUT, ON/OFF two buttons: IN/OUT button switches input voltage and output voltage display, long press can switch output current output power display; ON/OFF button control output ON or OFF, long press can Set the default output status of the next power-on to be ON or OFF. CC is the current setting potentiometer, clockwise rotation, can increase the set current, when the load current reaches the set current, enter the constant current state, the CC constant current indicator (red) lights up; the right CV is the voltage setting The potentiometer rotates clockwise to increase the output voltage. The ON indicator is an output status indicator that lights up when there is voltage at the output, otherwise it is off. Instructions: 1. Use as a common buck-boost module with overcurrent protection (1) Adjust the CV constant voltage device so that the output voltage reaches the voltage you want. (2) Use the multimeter 10A current file to measure the output short-circuit current (directly connect the two test leads to the output terminal), and adjust the CC constant current potentiometer to make the output current reach the predetermined overcurrent protection value. (3)(For example, if the current value displayed by the multimeter is 2A, then the maximum current can only be 2A when you use the module, and the red constant voltage constant current indicator will be on when the current reaches 2A, otherwise the indicator will be off) Note: When using in this state, there is a current sampling resistor at the output, there will be a voltage drop of 0~0.2V after the load is connected, and at the same time, the input wire and the output wire will have a certain line voltage drop when the current is large. This is normal! 2. Use as a battery charger Modules without constant current function cannot be used to charge the battery. Because the voltage difference between the battery and the charger that consumes electricity is too large, the charging current is too large, causing damage to the battery. Therefore, the battery should be used at the beginning. Stream charging, automatically switch back to constant voltage charging when charging to a certain extent electronicstore.pk

Mini MP1584EN DC-DC BUCK Adjustable Step Down Module 4.5V-28V Input 0.8V-20V Output The MP1584 is a high frequency step-down switching regulator with an integrated internal high-side high voltage power MOSFET Specifications: Model:MP1584 Name: DC-DC step-down module Input Voltage: 4.5V ~ 28V Output voltage: 0.8V ~ 20V Output Current: 3A (Max) Conversion efficiency: 96% (maximum) Output Ripple: <30mV Switching frequency: 1.5MHz (highest) typically 1MHz Operating Temperature: -45°C ~ +85°C Size: 22mm * 17mm (L * W ) Application areas: DIY mobile power monitor power supply power buggies camera power supply car power communications equipment supply,etc.

The XL7015 DC-DC step-down module is a high efficiency, high voltage step-down DC-DC converter that provides high 0.8A output current capability, low ripple, excellent linearity, and load regulation, and high input voltage. 80V, far more than 2596 and other modules. The chip has multiple protection mechanisms built in. Can be applied to electric vehicle controllers, etc. Features: 5 v to 80 v input voltage range wide. The output voltage from 5 v to 20 v adjustable. The minimum pressure drops 1 v. 0.8 The biggest switch current. Recommend the output power is less than 7 w. Shut off built-in overheating protection, output short circuit protection, over current protection. Good linear with load regulation. The board size: 16 mm * 44 mm. Wiring Instructions: VIN: input voltage (5 v - 80 - v). The GND: input voltage side. The VOUT: output voltage (5 v - 20 v). The GND: output voltage to end. Package Includes: 1XXL7015 DC-DC Buck Converter Step Down Module 5V-80V Wide Voltage Input 7005A Super Than LM2596